Join Us

How to Bleed a Hydraulic Bottle Jack?

Author: Geym

Feb. 20, 2024

hydraulic bottle jack is a powerful tool that can lift heavy loads with ease. However, over time, air can get trapped in the hydraulic system, which can reduce the jack’s lifting capacity and make it less effective. Bleeding the hydraulic system is a simple process that can help restore the jack’s performance. In this article, we will discuss how to bleed a hydraulic bottle jack.

 

Step 1: Release the Pressure

Before you begin bleeding the hydraulic system, you need to release any pressure that may be in the jack. To do this, locate the release valve on the jack. This is usually located on the side or the bottom of the jack. Turn the release valve counterclockwise to release any pressure that may be in the jack. Be sure to turn the valve slowly to avoid sudden release of pressure.

 

Step 2: Fill the Jack with Hydraulic Fluid

Next, you need to fill the jack with hydraulic fluid. To do this, locate the filler plug on the jack. This is usually located on the top of the jack. Remove the filler plug and fill the jack with hydraulic fluid. Be sure to use the correct type of hydraulic fluid for your jack. Check the owner’s manual or the manufacturer’s website to find out which type of hydraulic fluid is recommended for your jack. Overfilling the jack can cause damage to the jack, so be sure to fill it to the recommended level.


100 Ton Hydraulic Bottle Jack

 100-Ton Hydraulic Bottle Jack

Step 3: Replace the Filler Plug

Once you have filled the jack with hydraulic fluid, replace the filler plug and tighten it securely. Be sure to wipe away any excess hydraulic fluid that may have spilled during the filling process.

 

Step 4: Build Up Pressure in the Jack

Now that the jack is filled with hydraulic fluid, you need to build up pressure in the jack. To do this, pump the jack handle several times. This will help to build up pressure in the jack and prepare it for bleeding.

 

Step 5: Locate the Bleed Valve

Next, you need to locate the bleed valve on the jack. This is usually located on the side or the bottom of the jack. The bleed valve is used to release any air that may be trapped in the hydraulic system.


 8 Ton Hydraulic Double Ram Bottle Jack

  8 Ton Hydraulic Double Ram Bottle Jack

Step 6: Open the Bleed Valve

Turn the bleed valve counterclockwise to open it. This will allow any air that may be trapped in the hydraulic system to escape. You should hear a hissing sound as the air is released. Be sure to turn the valve slowly to avoid sudden release of pressure.

 

Step 7: Pump the Jack Handle

Once the bleed valve is open, pump the jack handle several more times. This will help to build up pressure in the jack and force any air that may be trapped in the hydraulic system out through the bleed valve.

 

Step 8: Close the Bleed Valve

After pumping the jack handle several times, turn the bleed valve clockwise to close it. This will prevent any hydraulic fluid from leaking out of the jack.


 2 Ton Hydraulic Bottle Jack

 2 Ton Hydraulic Bottle Jack

Step 9: Repeat the Process

Repeat steps 6-8 until no more air bubbles come out of the bleed valve. This may take several attempts, depending on how much air is trapped in the hydraulic system. Be patient and take your time to ensure that all the air is bled from the system.

 

Step 10: Test the Jack

Once you have bled all the air from the hydraulic system, test the jack to make sure it is working properly. Place a load on the jack and pump the handle to lift the load. If the jack is working properly, it should lift the load with ease. If you notice any problems, such as reduced lifting capacity or slow lifting speed, you may need to bleed the hydraulic system again.

 

In conclusion, bleeding a hydraulic bottle jack is a simple process that can help restore the jack’s performance. By following these steps, you can ensure that your jack is working properly and is ready to handle any heavy-lifting tasks you may have. Remember to always use the correct type of hydraulic fluid for your jack and to follow the manufacturer’s instructions for proper use and maintenance.


242

0

Comments

0/2000

All Comments (0)

Previous: None

Next: None

Guest Posts

If you are interested in sending in a Guest Blogger Submission,welcome to write for us!

Your Name: (required)

Your Email: (required)

Subject:

Your Message: (required)

0/2000